Diferenças

Aqui você vê as diferenças entre duas revisões dessa página.

--- phone:f1000 [2016/10/21 20:27] – facsi
+++ phone:f1000 [2022/11/07 08:31] (atual) – edição externa 127.0.0.1
@@ Linha 1: / Linha 1: @@
 ======UTStarcom F1000 / F1000G SIP Phone======
-{{description>The F1000 is a SIP protocol wifi phone manufactured by UTStarcom in 2005.
+=====Description=====
-It supports Wireless B on F1000 and wireless B/G on F1000G.}}
+The F1000 is a SIP protocol wifi phone manufactured by UTStarcom in 2005.
+It supports Wireless B on F1000 and wireless B/G on F1000G.
+=====Agere T8307 Data Sheet=====
+Processor
+https://www.tripleoxygen.net/wiki/_media/phone/t8307_v0.2_datasheet.pdf
+LCD
+https://www.tripleoxygen.net/wiki/_media/phone/gp-lcd-spec_kgm082b0_.pdf
 =====Serial Interface=====
@@ Linha 10: / Linha 18: @@
 It is possible to access it by two means.
-====One====
-Open the device (which may crack the housing since it is difficult to open)
-Check the board for TX, RX and GND test points.
-====Two====
+==== Recommended way ====
 The USB port at the bottom isn't a normal USB port. Its pinout configuration is:
@@ Linha 25: / Linha 31: @@
 Note that it uses the additional unused 4th pin on the USB cable.
+==== Second way (not recommended) ====
+Open the device (which may crack the housing since it is difficult to open). Check the board for TX, RX and GND test points.
@@ Linha 45: / Linha 53: @@
 On this step you want to search for the following text:
+<code>
 httpInit: Upload RPM successfully initialized.
 httpInit: System File Registry successfully initialized.
@@ Linha 59: / Linha 67: @@
 httpPwdConfAdd OK dXNlcjo4ODg4ODg=
 before taskSpawn sysPause
+</code>
 Take a closer look on this 2 lines:
 httpPwdConfAdd OK YWRtaW46ODRKaTIzZGphVw==
 httpPwdConfAdd OK dXNlcjo4ODg4ODg=
@@ Linha 72: / Linha 82: @@
 You can change the admin password to anything you want by accessing the webpage.
-Now follow meisted_sd tutorial and after flashing a 4.50 version, do a factory reset via web menu using admin account. (»Unlocking the UTStarCom F1000)
+Now follow meisted_sd tutorial and after flashing a 4.50 version, do a factory reset via web menu using admin account.
 PS. I do not recommend the 4.50 version. I prefer flashing 3.80 because you cannot downgrade it or maybe cannot return to vonage's firmware by rewriting the vonages tftp link.
+===Meisted_sd flashing===
+Unlocking the UTStarCom F1000
+This unlocking guide was made in a large part
+from the unlocking guide 'rkworth' posted here:
+»www.vonage-forum.com/fto ··· 464.html
+I've added a few comments, which are [in brackets]
+and then taken the extra step to totally remove
+vonage from the phone. Here is his guide, and then
+mine follows at the end.
+-------------------------
+Password for firmware upgrade - utvonpw
+then-
+So I've managed to unlock the Vonage UT starcom F1000
+wifi phone from Vonage. I think it's a first because
+there's no other info on how to do this anywhere on the web.
+You'll need a Windows pc for this...
+The first thing to do is download the firmware from here:
+File name is F1000_V3.80st.exe
+just google for f1000 firmware.
+Run this self extracting archive - it's German but no need
+to worry - just accept the defaults.
+It should unpack 4 files.
+Next make sure your Vonage wifi phone is connected and registered
+i.e. you can make a call. [Here, the phone never actually has to
+connect to the internet. The password "utvonpw" is factory set
+into the phone. You just need it connected on your wireless]
+Scroll through the menus on your phone and choose Wi-Fi
+Settings / Network Parameters / Network Info.
+Take note of the IP address (you may not need this but it's
+handy to have). Mine is 192.168.1.14.
+Exit out of the Network Info menu and go to the Misc menu
+Select Local TFTP Update.
+At the Code prompt enter utvonpw
+You'll see a message that says TFTP is a long process..
+Select Update
+The Screen will say Connecting...
+Back to Windows PC and launch the fwupgrade.exe application
+After a split second you should see a phone list that shows the
+IP address we had earlier.
+Click Update
+You'll get a warning not to turn off either the Computer, Phone
+or Access Point...don't turn them off!
+Mine took about 45 seconds to push the firmware.
+The screen on the phone will read Processing...
+then Decompressing...
+Windows will say that the task was complete...you can close the
+updater by clicking Cancel
+Phone is still Decompressing 3 minutes later...
+Then it will switch off.
+***DO NOT TURN IT BACK ON**** or your work will be undone by Vonage!
+-------THIS STEP IS REALLY IMPORTANT-------
+Disconnect your broadband. [You never actually had to have it connected]
+Don't power it off, just disconnect either the phone cable if DSL or
+the Coax if on cable. It's important that your wireless network stays up.
+Check that you can no longer browse the internet on your windows pc.
+Turn the F1000 on and it will connect to your wireless network.
+It will try and register via your network but of course you are
+disconnected so it can't - this is good!
+Go to the Misc menu on the phone and select remote TFTP server - it
+should have a Vonage server address in here...change it to a single
+letter "a" (Or any other setting to remove the vonage URL)
+[This step isn't really needed if you keep the unit off a
+wireless connection and complete my steps at the end of
+this part. I've also been told this doesn't always work
+to keep the unit from getting provisioned again if it
+gets a wireless connection.]
+Turn the phone off
+Reconnect your broadband and ensure you CAN browse to a
+webpage or two.
+Turn phone on and it will connect to your wireless network but
+it will never Register as it can't find Vonage servers!
+Usng a web browser open the IP address that we remember from earlier.
+(This actually connects you to the phones internal web server)
+Login as user with password 888888 (six 8's)
+Click User Menu on the left and go immediately to SIP & RTP Config
 =====Provisioning file=====
@@ Linha 208: / Linha 336: @@
 #Manually config SIP timer=T1T24000T45000TimerB32000TimerFTimerHTimerDTimerJ
 </code>
+========
+This software can create provisioning files for F1000
+https://www.tripleoxygen.net/wiki/_media/phone/provisioning_1_1_42_x86.zip
+From: https://sourceforge.net/projects/provisioning/
@@ Linha 213: / Linha 346: @@
 [[http://web.quick.cz/lake/f1000_faq.htm|UTStarcom F1000 FAQ]]
+[[https://www.dslreports.com/forum/r31016698-Definitive-Unlock-for-Vonage-F-1000-UTstarcom|DSL Reports Post]]
+==== Acknowledgments ====
+People involved in discussions, tips, or general chat. List in alphabetical order.
+facsi, Steve Hiddenvision, Tripleoxygen