Tabela de conteúdos
Arcadyan VRV7006AW22-A-GR
Informações sobre o PowerBox GVT Arcadyan VRV7006AW22-A-GR xDSL modem/router. Teardown, hacking, unlocking (desbloqueio), firmwares, custom images, recuperação, bridge.
Disclaimer
Modifique o dispositivo somente se for o proprietário. A maioria destes são fornecidos pelo seu ISP em regime de comodato como parte do serviço de internet. Não faça modificações caso o aparelho não seja seu.
Todos os métodos de desbloqueio e material sobre modificações foram criados pelo O3 Labs e disponibilizados GRATUITAMENTE desde o dia de sua elaboração. Espalhem esta informação e ajudem a evitar que PICARETAS roubem e vendam estas informações por aí, seja no Mercado Livre ou por quaisquer outros meios.
Hardware
Clique na foto para abrir o álbum.
| SoC | PSB 80221 / VRX220 - Lantiq VDSL2/ADSL2/2+ DSL Gateway Solution ( MIPS 34Kc, 500 MHz ) |
|---|---|
| RAM | K4T1G164QG-BCF7 - Samsung 1 Gbit (128 MB) DDR2 SDRAM |
| Flash | MX30LF1GE8AB - MXIC 1 Gbit (128 MB) NAND |
| Switch | 4 ports 10/100 - Integrado ao SoC |
| USB | 1 x 2.0 |
| Wireless | BCM43217 - Broadcom 2×2 802.11b/g/n / 2.4 GHz |
| FXS | 1 ( Lantiq PEF 41068 ) |
| xDSL Line Driver | PSB 80108 - Lantiq |
| HPNA | Não |
| Serial | Sim |
| JTAG | ? |
Bootlog
ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 0000000c DDR autotuning Rev 1.0 DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 0000000c DDR autotuning Rev 1.0 DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-00032-gdf2992a-dirty-LANTIQ-v-2.2.89-1.00.03 (Jun 22 2015 - 15:25:48) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (MXIC MX30LF1GE8AB) 128 MiB Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000004620000 In: serial Out: serial Err: serial Net: Internal phy(FE) firmware version: 0xc40d vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS call arc_gpio_init !!! Hit any key to stop autoboot: 1 0 bootup_ok=[1] Writing to Nand... done Creating 1 MTD partitions on "nand0": 0x000000440000-0x000007c40000 : "mtd=4" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=4" UBI: MTD device size: 120 MiB UBI: number of good PEBs: 959 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 256 UBI: number of internal volumes: 1 UBI: number of user volumes: 5 UBI: available PEBs: 187 UBI: total number of reserved PEBs: 772 UBI: number of PEBs reserved for bad PEB handling: 9 UBI: max/mean erase counter: 9/0 Volume kernelA found at volume id 0 read 0 bytes from volume 0 to a4000000(buf address) Read [6322176] bytes ubi_error_number=[0] Volume sec_boot found at volume id 4 read 0 bytes from volume 4 to af000000(buf address) Read [1161216] bytes ## Starting application at 0xAF000000 ... < sec_boot: 31>: Decrypt kernel at a4000000 < sec_boot: 49>: kernel size = 1c0000 < arc_img_dec: 47>: data = a4000004 < arc_img_dec: 54>: < arc_img_dec: 75>: < arc_img_dec: 83>: < arc_img_dec: 89>: < arc_img_dec: 105>: ## Application terminated, rc = 0x0 ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-2.6.32.42 Created: 2015-06-12 10:09:54 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1834944 Bytes = 1.7 MiB Load Address: 80002000 Entry Point: 800061b0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Lantiq xDSL CPE VR9 mips_hpt_frequency = 250000000, counter_resolution = 2 [ 0.000000] Linux version 2.6.32.42 (anne_liang@sw6-builder.arcadyan.com.tw) (gcc version 4.3.3 (GCC) ) #1 Fri Jun 12 16:40:56 CST 2015 [ 0.000000] phym = 08000000, mem = 07f00000, max_pfn = 00007f00 [ 0.000000] Reserving memory for CP1 @0xa7f00000, size 0x00100000 [ 0.000000] CPU revision is: 00019556 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 07f00000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00007f00 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00007f00 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32258 [ 0.000000] Kernel command line: ubi.mtd=linux rootfsname=rootfsA rw rootfstype=ubifs ip=192.168.1.1:192.168.1.10::::eth0:on console=ttyS0,115200 ethaddr=xx:xx:xx:xx:xx:xx phym=128M mem=127M wlanm= panic=1 mtdparts=ifx_nand:1m(uboot),256k(ubootconfig),2m(glbcfg),1m(board_data),120m(linux),-(res) vpe1_load_addr=0x87f00000 vpe1_mem=1M init=/sbin/ltq_preinit root=ubi0:rootfsA active_bank=A update_chk=0 ubootver=U-Boot-2010.06-00032-gdf2992a-dirty-LANTIQ-v-2.2.89-1.00.03 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00058100 [ 0.000000] Readback ErrCtl register=00058100 [ 0.000000] Memory: 122932k/130048k available (3821k kernel code, 6944k reserved, 1274k data, 204k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:185 [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.000000] console [ttyS0] enabled [ 0.020000] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) [ 0.240000] Security Framework initialized [ 0.240000] Mount-cache hash table entries: 512 [ 0.250000] NET: Registered protocol family 16 [ 0.580000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.600000] bio: create slab <bio-0> at 0 [ 0.610000] SCSI subsystem initialized [ 0.610000] usbcore: registered new interface driver usbfs [ 0.610000] usbcore: registered new interface driver hub [ 0.620000] usbcore: registered new device driver usb [ 0.620000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.630000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.630000] pci 0000:00:00.0: PME# disabled [ 0.640000] pci 0000:00:00.0: PCI bridge, secondary bus 0000:01 [ 0.640000] pci 0000:00:00.0: IO window: disabled [ 0.650000] pci 0000:00:00.0: MEM window: 0x1c000000-0x1c0fffff [ 0.650000] pci 0000:00:00.0: PREFETCH window: disabled [ 0.660000] NET: Registered protocol family 8 [ 0.660000] NET: Registered protocol family 20 [ 0.660000] Switching to clocksource MIPS [ 0.670000] NET: Registered protocol family 2 [ 0.670000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.680000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.690000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.690000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.700000] TCP reno registered [ 0.700000] NET: Registered protocol family 1 [ 0.710000] gptu: totally 6 16-bit timers/counters [ 0.710000] gptu: misc_register on minor 63 [ 0.710000] gptu: succeeded to request irq 118 [ 0.720000] gptu: succeeded to request irq 119 [ 0.720000] gptu: succeeded to request irq 120 [ 0.730000] gptu: succeeded to request irq 121 [ 0.730000] gptu: succeeded to request irq 122 [ 0.740000] gptu: succeeded to request irq 123 [ 0.740000] IFX DMA driver, version ifxmips_dma_core.c:v1.1.5 [ 0.740000] ,(c)2009 Infineon Technologies AG [ 0.750000] Lantiq CGU driver, version 1.1.38, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.760000] vpe1_mem = 100000 [ 0.760000] Wired TLB entries for Linux read_c0_wired() = 0 [ 0.770000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.770000] Registering mini_fo version $Id$ [ 0.780000] JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.790000] msgmni has been set to 240 [ 0.790000] Infineon Technologies DEU driver version 2.0.0 [ 0.800000] Lantiq Technologies DEU Driver version 2.0.0 [ 0.800000] IFX DEU DES initialized (multiblock). [ 0.810000] Lantiq Technologies DEU Driver version 2.0.0 [ 0.810000] IFX DEU AES initialized (multiblock). [ 0.820000] Infineon Technologies DEU driver version 2.0.0 [ 0.820000] IFX DEU ARC4 initialized (multiblock). [ 0.830000] Infineon Technologies DEU driver version 2.0.0 [ 0.830000] IFX DEU SHA1 initialized. [ 0.840000] Infineon Technologies DEU driver version 2.0.0 [ 0.840000] IFX DEU MD5 initialized. [ 0.850000] Infineon Technologies DEU driver version 2.0.0 [ 0.850000] IFX DEU SHA1_HMAC initialized. [ 0.860000] Infineon Technologies DEU driver version 2.0.0 [ 0.860000] IFX DEU MD5_HMAC initialized. [ 0.870000] DEU driver initialization complete! [ 0.870000] io scheduler noop registered (default) [ 0.880000] HDLC line discipline maxframe=4096 [ 0.890000] N_HDLC line discipline registered. [ 0.890000] ifx_pmu_init: Major 252 [ 0.890000] Lantiq PMU driver, version 1.2.6, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.900000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.910000] Infineon Technologies RCU driver version 1.1.1 [ 0.910000] Lantiq LED Controller driver, version 1.1.3, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.920000] Lantiq (VRX) DSL CPE MEI driver, version 1.4.4, (c) 2013 Lantiq Deutschland GmbH [ 0.930000] ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC [ 0.940000] Register ASC (UART) to PMCU. [ 1.000000] Lantiq ASC (UART) driver, version 1.0.14, (c) 2001-2013 Lantiq Deutschland GmbH [ 1.010000] brd: module loaded [ 1.020000] loop: module loaded [ 1.020000] ifx_nand_init [ 1.020000] Probe for NAND flash... [ 1.020000] Checking if ONFI complient [ 1.030000] ONFI param page 0 valid [ 1.030000] ONFI flash detected, val i = 0 [ 1.030000] writesize: 2048, erasesize: 131072, chipsize: 134217728 [ 1.040000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (MXIC NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.080000] Bad eraseblock 561 at 0x000004620000 [ 1.110000] 6 cmdlinepart partitions found on MTD device ifx_nand [ 1.110000] Creating 6 MTD partitions on "ifx_nand": [ 1.110000] 0x000000000000-0x000000100000 : "uboot" [ 1.120000] 0x000000100000-0x000000140000 : "ubootconfig" [ 1.130000] 0x000000140000-0x000000340000 : "glbcfg" [ 1.130000] 0x000000340000-0x000000440000 : "board_data" [ 1.140000] 0x000000440000-0x000007c40000 : "linux" [ 1.140000] 0x000007c40000-0x000008000000 : "res" [ 1.150000] UBI: attaching mtd4 to ubi0 [ 1.150000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.160000] UBI: logical eraseblock size: 129024 bytes [ 1.160000] UBI: smallest flash I/O unit: 2048 [ 1.170000] UBI: sub-page size: 512 [ 1.170000] UBI: VID header offset: 512 (aligned 512) [ 1.180000] UBI: data offset: 2048 [ 1.380000] UBI: attached mtd4 to ubi0 [ 1.380000] UBI: MTD device name: "linux" [ 1.390000] UBI: MTD device size: 120 MiB [ 1.390000] UBI: number of good PEBs: 959 [ 1.400000] UBI: number of bad PEBs: 1 [ 1.400000] UBI: max. allowed volumes: 128 [ 1.410000] UBI: wear-leveling threshold: 4096 [ 1.410000] UBI: number of internal volumes: 1 [ 1.420000] UBI: number of user volumes: 5 [ 1.420000] UBI: available PEBs: 187 [ 1.430000] UBI: total number of reserved PEBs: 772 [ 1.430000] UBI: number of PEBs reserved for bad PEB handling: 9 [ 1.440000] UBI: max/mean erase counter: 9/0 [ 1.440000] UBI: image sequence number: 0 [ 1.450000] Gluebi: Found kernel commandline option 'rootfsname=rootfsA' [ 1.450000] UBI: background thread "ubi_bgt0d" started, PID 220 [ 1.460000] Gluebi: mtd 'rootfsA' set to be root filesystem [ 1.470000] Lantiq SSC driver, version 2.4.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 1.470000] Lantiq SPI EERPOM driver, version 1.1.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 1.480000] PPP generic driver version 2.4.2 [ 1.490000] PPP Deflate Compression module registered [ 1.490000] PPP BSD Compression module registered [ 1.500000] PPP MPPE Compression module registered [ 1.500000] NET: Registered protocol family 24 [ 1.510000] PPPoL2TP kernel driver, V1.0 [ 1.510000] IMQ driver loaded successfully. [ 1.520000] Hooking IMQ before NAT on PREROUTING. [ 1.520000] Hooking IMQ after NAT on POSTROUTING. [ 1.530000] IFX SWITCH API, Version 1.2.6 [ 1.530000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.540000] Switch API: PCE MicroCode loaded !! [ 1.540000] [ 1.540000] GPHY:!!!! chip-ID :4, chipID.family_ver:2 [ 1.550000] Init GPHY Driver for A12 !! [ 1.550000] Init GPHY Driver for A12 !! [ 1.670000] GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR (FE MODE) : 80554000 [ 2.690000] IFX GPHY driver FE Mode, version ifxmips_xrx_gphy: V1.1.1 - Firmware: c434 [ 3.540000] GPHY LED poll thread created.. [ 3.540000] GPHY RMON poll thread created.. [ 3.540000] res = 87998800 [ 3.550000] Registered led device: 107 [ 3.550000] Registered led device: 111 [ 3.550000] Registered led device: 106 [ 3.560000] start 8785fab8 .. [ 3.560000] start 878ac9b8 .. [ 3.570000] Registered led device: 108 [ 3.570000] Registered led device: 110 [ 3.570000] Registered led device: 117 [ 3.580000] Registered led device: 113 [ 3.580000] Registered led device: 116 [ 3.580000] Registered led device: 115 [ 3.590000] Registered led device: 104 [ 3.590000] Registered led device: 114 [ 3.600000] Lantiq LED driver, version 1.1.4, (c) 2001-2013 Lantiq Deutschland GmbH [ 3.600000] Mirror/redirect action on [ 3.610000] u32 classifier [ 3.610000] Performance counters on [ 3.610000] input device check on [ 3.620000] Actions configured [ 3.620000] Netfilter messages via NETLINK v0.30. [ 3.630000] nf_conntrack version 0.5.0 (1923 buckets, 7692 max) [ 3.630000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 3.640000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 3.650000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 3.650000] ctnetlink v0.93: registering with nfnetlink. [ 3.660000] nf_conntrack_rtsp v0.6.21 loading [ 3.660000] xt_time: kernel timezone is -0000 [ 3.670000] IPv4 over IPv4 tunneling driver [ 3.670000] GRE over IPv4 tunneling driver [ 3.690000] ip_nat_rtsp v0.6.21 loading [ 3.690000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.690000] TCP cubic registered [ 3.700000] Initializing XFRM netlink socket [ 3.700000] NET: Registered protocol family 10 [ 3.730000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.730000] NET: Registered protocol family 17 [ 3.730000] NET: Registered protocol family 15 [ 3.740000] Ebtables v2.0 registered [ 3.740000] NET: Registered protocol family 8 [ 3.750000] atmpvc_init() failed with -17 [ 3.750000] lec.c: Jun 12 2015 16:35:15 initialized [ 3.760000] mpc.c: Jun 12 2015 16:35:08 initialized [ 3.760000] KOAM is loaded successfully. [ 3.760000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 3.770000] All bugs added by David S. Miller <davem@redhat.com> [ 3.830000] UBIFS: recovery needed [ 3.890000] UBIFS: recovery completed [ 3.890000] UBIFS: mounted UBI device 0, volume 1, name "rootfsA" [ 3.900000] UBIFS: file system size: 40771584 bytes (39816 KiB, 38 MiB, 316 LEBs) [ 3.900000] UBIFS: journal size: 8128512 bytes (7938 KiB, 7 MiB, 63 LEBs) [ 3.910000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.920000] UBIFS: default compressor: lzo [ 3.920000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 3.930000] VFS: Mounted root (ubifs filesystem) on device 0:10. [ 3.930000] Freeing unused kernel memory: 204k freed [ 3.940000] Please be patient, while OpenWrt loads ... arca.dbus.mng: is ready agent_handler(236):arca.dbus.misc: is ready Please press Enter to activate this console. MD5=[08a378558b3381351db057eb77491bf5] [ 9.020000] IFXOS, Version 1.5.17 (c) Copyright 2009, Lantiq Deutschland GmbH @arc_wan_type = 0 [ 10.030000] [ 10.030000] [ 10.030000] Lantiq CPE API Driver version: DSL CPE API V4.16.6-pd1 [ 10.040000] [ 10.040000] Predefined debug level: 3 AUTO!!!! @@ load_ppa_modules.sh start @@ wanphy_phymode=0 @@ wanphy_tc=0 @ load_modules ATM 0 load start load done load ... @ PPA is ready /opt/lantiq/bin/dsl_cpe_control -D3 -i05_00_04_00_0C_01_00_07 -f /firmware/xcpe_hw.bin -M0 -T1:0x1:0x1_2:0x1:0x1 -A /opt/lantiq/bin/vdsl.scr -a /opt/lantiq/bin/adsl.scr -n /etc/init.d/xdslrc.sh & [ 15.400000] MEI_DRV: MEI_IfxRequestIrq(IRQ = 55, .., ), lock = 1 [ 15.400000] [ 18.580000] hnd: module license 'Proprietary' taints kernel. [ 18.580000] Disabling lock debugging due to kernel taint [xdslrc.sh] DSL_NOTIFICATION_TYPE=DSL_INTERFACE_STATUS [xdslrc.sh] DSL_INTERFACE_STATUS=READY [xdslrc.sh] DSL_XTU_STATUS= [xdslrc.sh] Next_xTM_Mode= [xdslrc.sh] DSL_TC_LAYER_STATUS= [ 21.260000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 21.270000] Neither SPROM nor OTP has valid image [ 21.280000] srom rev:0 [ 21.320000] wlan0: Broadcom BCMa8db 802.11 Wireless Controller 6.37.14.88 (r461005 WLTEST) 2.4G [ 22.580000] TAPI, Version 4.10.4.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 22.780000] Lantiq MIPS34KEc MPS driver, version 2.2.7.0, (c) 2006-2010 Lantiq Deutschland GmbH [ 22.820000] Lantiq VMMC device driver, version 1.15.0.4, (c) 2006-2013 Lantiq Deutschland GmbH [ 22.980000] IFXUSB: ifxusb_hcd: version 3.2 B140220 [ 22.980000] IFXUSB: OPTION: __IS_VR9__ [ 22.990000] IFXUSB: OPTION: __UEIP__ [ 22.990000] IFXUSB: OPTION: __PHY_LONG_PREEMP__ [ 22.990000] IFXUSB: OPTION: __UNALIGNED_BUF_ADJ__ [ 23.000000] IFXUSB: OPTION: __DEBUG__ [ 23.000000] IFXUSB: OPTION: __ENABLE_DUMP__ [ 23.010000] IFXUSB: OPTION: __NEW_COC__ [ 23.010000] IFXUSB: OPTION: __IS_HOST__ [ 23.020000] IFXUSB: __IS_FIRST__ [ 23.020000] IFXUSB: __DYN_SOF_INTR__ [ 23.020000] IFXUSB: __HOST_COC__ [ 23.030000] IFXUSB: __UEIP__ [ 23.030000] IFXUSB: __DO_OC_INT__ [ 23.040000] IFXUSB: __INTRNAKRETRY__ [ 23.040000] IFXUSB: __INTRINCRETRY__ [ 23.060000] Chip Version :0002 BurstSize=4 [ 23.660000] IFXUSB: USB core #0 soft-reset [ 23.960000] IFXUSB: USB core #0 soft-reset [ 23.970000] ifxusb_hcd ifxusb_hcd: IFX USB Controller [ 23.970000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1 [ 23.980000] ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000 [ 23.980000] drivers/char/ifxmips_gpio.c:1182:ifx_gpio_pin_reserve: Pin ID 0 (port 0, pin 0) has been reserved by module LED from kernel module! [ 24.000000] IFXUSB: Register USB VBus Failed!! [ 24.000000] IFXUSB: Init: Power Port (0) [ 24.020000] usb usb1: configuration #1 chosen from 1 choice [ 24.030000] hub 1-0:1.0: USB hub found [ 24.030000] hub 1-0:1.0: 1 port detected [ 24.120000] Initializing USB Mass Storage driver... [ 24.130000] usbcore: registered new interface driver usb-storage [ 24.130000] USB Mass Storage support registered. [ 24.840000] fuse init (API version 7.13) [ 24.920000] NTFS driver 2.1.29 [Flags: R/O MODULE]. [ 24.990000] ffp: Unknown symbol ffp_del_entry_hook [ 24.990000] ffp: Unknown symbol ffp_ipv6_add_entry_hook [ 25.000000] ffp: Unknown symbol ffp_input [ 25.000000] ffp: Unknown symbol ffp_get_timeout_hook [ 25.010000] ffp: Unknown symbol ffp_get_ppp_info [ 25.010000] ffp: Unknown symbol ffp_ipv6_input [ 25.020000] ffp: Unknown symbol ffp_ipv6_del_entry_hook [ 25.020000] ffp: Unknown symbol ffp_add_entry_hook [ 25.030000] ffp: Unknown symbol ffp_ipv6_output_hook [ 25.030000] ffp: Unknown symbol ffp_get_pppol2tp_info [ 25.040000] ffp: Unknown symbol ffp_output_hook [ 25.040000] ffp: Unknown symbol imq_ffp_enqueue [ 25.050000] ffp: Unknown symbol ffp_fwd_hook [ 25.050000] ffp: Unknown symbol ffp_ipv6_get_timeout_hook [ 25.090000] ifx_ppa_init - init succeeded **************** boot ************************** wlan_start************************* b/g/n-mode wireless security WPA/WPA2 wireless security cipher TKIP+CCMP maclist: Enable WPS... Restart WLAN 0 ....... [ 27.990000] device eth0 entered promiscuous mode [ 28.000000] device wlan0 entered promiscuous mode [ 29.270000] udev: starting version 142 [autowandetect] argv=boot [autowandetect] ==> g_nWanDetect=1, g_nWanType=0 (0:AD,1:Eth,2:VD) [ 31.310000] VoIP Driver, Rev. 1.0.0, (c) 2013-2015 Arcadyan Technology Corp. [ 31.310000] voip_proc_init() [ 31.320000] [ 31.320000] voip_init: VoIP registration completed successfully killall: bpalogin: no process killed killall: bpalogin: no process killed killall: listen: no process killed hb done ECO_mode disable! Jan 1 00:00:34 crond[2431]: crond: crond (busybox 1.18.5) started, log level 8 Jan 1 00:00:34 miniupnpd[2439]: HTTP listening on port 37432 Jan 1 00:00:34 miniupnpd[2439]: HTTP IPv6 address given to control points : [fddd:3b7:e7c6:1234:5edc:96ff:fea3:a10e] Jan 1 00:00:34 miniupnpd[2439]: Listening for NAT-PMP traffic on port 5351 [ 36.100000] voip_initialize_cmd Trigger UP TR069 Module. Open /etc/samba/smbpasswd failed Command: touch /etc/samba/smbpasswd private_usb_samba_shared_entries_section_config Line 585: I'm Here try to start samba daemon Create a task to start smb start daemon Command: /etc/init.d/samba start Cfg ID: ARC_WLAN_24G_SSID_x_WPA_Passphrase, Idx1: 1, Idx2: -2147483648, Default value unexist! SYS_QUEUE_Create: queueId = 32769, queueName = VOICEQ, queueSize = 28 SYS_QUEUE_Create: queueId = 65538, queueName = tqueue, queueSize = 184 SYS_QUEUE_Create: queueId = 98307, queueName = sip, queueSize = 844 SYS_QUEUE_Create: queueId = 131076, queueName = VOICEIVRM, queueSize = 12 SYS_QUEUE_Create: queueId = 163845, queueName = VOICEIVRM, queueSize = 12 SYS_QUEUE_Create: queueId = 196614, queueName = VOICEIVRM, queueSize = 12 SYS_QUEUE_Create: queueId = 229383, queueName = VOICEIVRM, queueSize = 12 Finish creating a task to start smb Call Update Tr69 Rule.
Agradecimentos
Pessoas envolvidas em discussões, dicas ou bate papo em geral. Lista em ordem alfabética.