====== ZTE ZXHN F6600P ====== {{description>Informações sobre a ZTE ZXHN F6600P GPON ONT/ONU. Teardown, hacking, unlocking (desbloqueio), firmwares, custom images, recuperação, bridge.}} ===== Disclaimer ===== Todas as informações, métodos, procedimentos, firmwares, aplicativos e material sobre modificações e configurações postadas neste wiki foram criados pelo O3 Labs (salvo menção em contrário) e disponibilizadas **GRATUITAMENTE** desde o dia de sua elaboração. Denuncie quando possível quaisquer tentativas de venda destes material. ===== Hardware ===== {{:ont:zte:zte-f6600p-a-w.jpg?direct&400 |}} {{ :ont:zte:zte-f6600p-b-w.jpg?direct&400| }} ---- {{:ont:zte:zte-f6600p-c-w.jpg?direct&400 |}} {{ :ont:zte:zte-f6600p-d-w.jpg?direct&400|}} ---- ^ SoC | ZTE ZXIC ZX279128S | ^ CPU | 2 x Cortex-A9 @ 1 GHz | ^ RAM | 512 MB - Nanya NT5CC256M16ER-EK | ^ Flash | 256 MB - Kioxia TC58BVG1S3HTAI0 | ^ LAN | 4 x 1 Gbit/s | ^ USB | 1 x USB 2.0 | ^ Wireless 2.4 GHz| MediaTek MT7916AN + MT7976DN | ^ Wireless 5 GHz| MediaTek MT7916AN + MT7976DN | ^ XPON Laser Driver | ? | ^ Acoplamento fibra | SC/APC | ^ FXS | 1 porta - Skyworks Si3219FM1 | ^ HPNA | - | ^ Serial | Sim | ^ JTAG | - | ^ Alimentação | DC 12 V / 1.5 A | ^ Credenciais padrão | admin / - | ^ IP LAN padrão | 192.168.1.1 | ===== Bootlog ===== Boot NAND start read bootheader start read secondboot non secure boot Jump enter bootloader... crpm init enter crpm init done ddr init done serial init start serial init done NAND non secure uboot backup header!! Jump U-Boot 2013.04 (May 11 2022 - 14:01:33) CPU : ZX279128S@A9,1000MHZ Board: ZTE zx279128sevb I2C: ready DRAM: 512 MiB ,20000000,60000000 product_vid = 157 vid=157-F6600P output gpio:56, value=1, 0 output gpio:57, value=1, 0 output gpio:58, value=1, 0 output gpio:59, value=1, 0 mtk reset,45,55 bootsel=1 NAND: Manu ID: 0x98, Chip ID: 0xda (Toshiba NAND 256MiB 3,3V 8-bit) 256 MiB !mtdpart=0x1,offset=0x0,mtdpartoffset=0x180000,mtdPartsize=0x80000,length=0x20000 In: serial Out: serial Err: serial clk_pll env is not setted, core clk won't change Net: enter ref_clk_set.. mode = 0 . enter pll_cfg_fractional ref_clk_set success! gpon serdes init rxpll_ready addr 0x9400004c before value is 38000 addr 0x9400004c after value is 381ff eth0 Hit 1 to upgrade software version Hit any key to stop autoboot: 3  2  1  0 addr=1a00000 addr=6a00000 select=0x0 search=0x2 !mtdpart=0x6,offset=0x0,mtdpartoffset=0x200000,mtdPartsize=0x400000,length=0x1000 tmp=0x00000001, value=1 select=0x1 search=0x2 ---mtdparts_init--current_mtd_partnum=1- dev id: type = 2, num = 0, size = 0xffffffff, mtd_id = single part part : name = rootfs0, size = 0x01900000, offset = 0x01a20000 part : name = rootfs1, size = 0x01820000, offset = 0x06a20000 --- jffs2_part_info: partition number 1 for device nand0 (single part) jffs2_part_info:rootfs1,6a20000 ### JFFS2 loading '0uImage' to 0x44000000 Scanning JFFS2 FS: .................. done. ### JFFS2 load complete: 3592694 bytes loaded to 0x44000000 !mtdpart=0x0,offset=0x0,mtdpartoffset=0x0,mtdPartsize=0x180000,length=0x80000 lseek=0x42072800 cmdline=U-Boot V9.0.10P10N1 20220511143326 ## Booting kernel from Legacy Image at 44000000 ... Image Name: Linux Kernel Image Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3592630 Bytes = 3.4 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK ---------------------- |-->setup versioninfo tag... Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.1.25 (@9eaa6be541cf) (gcc version 4.9.3 (GCC) ) #225 SMP Thu Nov 3 22:28:25 CST 2022 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: ZTE ZX279128S Ignoring memory range 0x0 - 0x40000000 Ignoring memory block 0x0 - 0x20000000 in function:early_mem line: 810 zxic_mem_size = 0x20000000 zx279128_reserve_mem,264 ZX_RESERVE_MEM_SIZE is 2600000, 26 modename:bbx addr:5d800000 size:000f4000 [bbxMemNotify][450]bbx get address ok! [bbxMemNotify][451]s_dwBbxBaseAddr=0x5d800000,s_dwBbxRsvMemLen=0x000f4000 Memory policy: Data cache writealloc ======= zx_map_io ======= BUG: mapping for 0x00400000 at 0xf0000000 out of vmalloc space BUG: mapping for 0x00800000 at 0xf0100000 out of vmalloc space BUG: mapping for 0x00a20000 at 0xf0200000 out of vmalloc space BUG: mapping for 0x00c00000 at 0xf9602000 out of vmalloc space BUG: mapping for 0x94000000 at 0xf0400000 out of vmalloc space BUG: mapping for 0x94100000 at 0xf0500000 out of vmalloc space BUG: mapping for 0x94200000 at 0xf0600000 out of vmalloc space BUG: mapping for 0x94400000 at 0xf0700000 out of vmalloc space BUG: mapping for 0x9a100000 at 0xf0800000 out of vmalloc space BUG: mapping for 0x00d00000 at 0xf0900000 out of vmalloc space BUG: mapping for 0x92000000 at 0xf4000000 out of vmalloc space BUG: mapping for 0x00200000 at 0xf0a00000 out of vmalloc space BUG: mapping for 0x9fe00000 at 0xf0f00000 out of vmalloc space BUG: mapping for 0x09100000 at 0xf0b00000 out of vmalloc space BUG: mapping for 0x09400000 at 0xf0c00000 out of vmalloc space BUG: mapping for 0x09300000 at 0xf0d00000 out of vmalloc space BUG: mapping for 0x09200000 at 0xf0e00000 out of vmalloc space dfffc000--- BUG: mapping for 0x5da00000 at 0xf1000000 out of vmalloc space PERCPU: Embedded 11 pages/cpu @dd3d8000 s14752 r8192 d22112 u45056 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyAMA0,115200n8 root=/dev/mtdblock9 ro rootfstype=jffs2 mem=512M; U-Boot V9.0.10P10N1 20220511143326 0x6a00000 0x1 0x83 0x8f PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 469416K/524288K available (4805K kernel code, 350K rwdata, 1688K rodata, 208K init, 2187K bss, 54872K reserved, 0K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xf0000000 ( 248 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc065f628 (6494 kB) .init : 0xc0660000 - 0xc0694000 ( 208 kB) .data : 0xc0694000 - 0xc06eb880 ( 351 kB) .bss : 0xc06eb880 - 0xc090e850 (2188 kB) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. Additional per-CPU info printed with stalls. NR_IRQS:16 nr_irqs:16 16 L2C: platform modifies aux control register: 0x02030000 -> 0x32430000 L2C: platform provided aux values permit register corruption. L2C: DT/platform modifies aux control register: 0x02030000 -> 0x32430000 L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 16 ways, 256 kB L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x76430001 sched_clock: 64 bits at 500MHz, resolution 2ns, wraps every 4398046511103ns clocksource arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x400081c0 - 0x400081f4 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (3981.31 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 2048 KiB pool for atomic coherent allocations product_vid = 157 current_board=c06a6928 0,c3ffffa,c3ffffa 1,e0003c,e0003c 2,555ffff,555ffff 3,3e3f85,3e3f85 output gpio:56, value=1, 0 output gpio:57, value=1, 0 output gpio:58, value=1, 0 output gpio:59, value=1, 0 output gpio:51, value=0, 1 output gpio:2, value=0, 1 bootsel=1 hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. Serial: AMBA PL011 UART driver 94404000.serial: ttyAMA0 at MMIO 0x94404000 (irq = 19, base_baud = 0) is a console [ttyAMA0] enabled 94405000.serial: ttyAMA1 at MMIO 0x94405000 (irq = 20, base_baud = 0) is a (622):creat proc files for watchdog!!! (626):Starting Watchdog Timer... arm A9 regs f0100620 cpu1 watchdog: heartbeat 20 sec, clock 3906250,max heartbeat 1099 enable watchdog in cpu0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 synopsys pcie probe enter!!!!!! pcie0 irq is 37 pcie1 irq is 38 synopsys pcie0 controller setting synopsys pcie0 controller waitting L0 state pcie0 link up,gen1,cnt 23! synopsys pcie1 controller setting synopsys pcie1 controller waitting L0 state pcie1 link up,gen2,cnt 11! PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] PCI: bus0: Fast back to back transfers disabled PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [mem 0x20000000-0x27ffffff] pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] PCI: bus1: Fast back to back transfers disabled pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20107fff 64bit] pci 0000:01:00.0: BAR 4: assigned [mem 0x20108000-0x20108fff 64bit pref] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x100fffff 64bit pref] pci 0000:00:00.0: BAR 2: assigned [mem 0x10100000-0x10107fff 64bit] pci 0000:00:00.0: BAR 4: assigned [mem 0x10108000-0x10108fff 64bit pref] futex hash table entries: 512 (order: 2, 16384 bytes) ntfs: driver 2.1.32 [Flags: R/W]. jffs2: version 2.2. (NAND)  2001-2006 Red Hat, Inc. fuse init (API version 7.23) io scheduler noop registered (default) SCSI Media Changer driver v0.25 ID of nandflash: 0x1590da98 find:TC58BVG1S3HTA00 nand: device found, Manufacturer ID: 0x98, Chip ID: 0xda nand: Toshiba NAND 256MiB 3,3V 8-bit nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 8 bit device! Scanning device for bad blocks Bad eraseblock 1536 at 0x00000c000000 Bad eraseblock 1537 at 0x00000c020000 ##########verinfo=U-Boot V9.0.10P10N1 20220511143326 0x6a00000 0x1 0x83 0x8f ##########u32CurrBaseAddress=6a00000,1 ##########u32CurrBaseAddress=6a00000,1 kernel=kernel2,6a00000,5000000 size=4fe0000,offset=6a20000 Creating 10 MTD partitions on "denali-nand": 0x000000000000-0x000010000000 : "whole flash" 0x000000000000-0x000000200000 : "u-boot" 0x000000200000-0x000000600000 : "others" 0x000000600000-0x000000a00000 : "parameter tags" 0x000000a00000-0x000000e00000 : "wlan" 0x000000e00000-0x000001600000 : "usercfg" 0x000001600000-0x000001a00000 : "middleware" 0x000001a00000-0x000006a00000 : "kernel1" 0x000006a00000-0x00000ba00000 : "kernel2" 0x000006a20000-0x00000ba00000 : "rootfs" spi bootsel======1 zx_spi_probe...master->bus_num:0 SPI0 probed PPP generic driver version 2.4.2 NET: Registered protocol family 24 usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver cdc_ncm ZX_VA_TOP_CRM+0x4C=0x3cfff usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usblp usbcore: registered new interface driver usbserial usbcore: registered new interface driver option usbserial: USB Serial support registered for GSM modem (1-port) I2C probe start! zx_i2c_probe i2c-1 i2c-1->clk is dc479860 ,clk rate is 25000000 I2C probe successed! Synopsys Designware Multimedia Card Interface Driver usbcore: registered new interface driver usbhid usbhid: USB HID core driver zx tempsensor: zx_bsp_tempsensor.regs = 0xf0500034,&(zx_bsp_tempsensor.regs->cfg)= 0xf0500034 bsp_temp_start,val = 0x2ee (624):creat proc files for temper sensor!!! (629):temper sensor is running... zx tempsensor: work clock 0 zx tempsensor: selector0's int num 23 allocated. zx tempsensor: selector1's int num 24 allocated. zx tempsensor: selector2's int num 25 allocated. nf_conntrack version 0.5.0 (7334 buckets, 29336 max) ip_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. Bridge firewalling registered Ebtables v2.0 registered 8021q: 802.1Q VLAN Support v1.8 logger: created 1024K log 'logger_main' major '99' logger: created 512K log 'logger_sys' major '101' ----------netif_flag_init_net--------! ----------wb_init_net--------! 11930:22:55 [KMLDSNP][Error] [br_mld.c(3828)mld_register] protocol =131 11930:22:55 [KMLDSNP][Error] [br_mld.c(3828)mld_register] protocol =132 11930:22:55 [KMLDSNP][Error] [br_mld.c(3828)mld_register] protocol =143 zte--oss cpu usage module init systools version:v0.7.0 Init Common Switch Module Init Common Switch Module Success Init Common Gpondrv Module Init Common Gpondrv Module Success Registering SWP/SWPB emulation handler random: nonblocking pool is initialized VFS: Mounted root (jffs2 filesystem) readonly on device 31:9. Freeing unused kernel memory: 208K (c0660000 - c0694000) This architecture does not have kernel memory protection. ====================================================== mounting /dev/mtdblock3 to /tagparam, wait ... ====================================================== Pre-initialization script ... Mounting ramdisk at /var Mounting ramdisk at /mnt Mounting /dev/mtdblock5 to /userconfig Mount ok! Mounting /dev/mtdblock6 to /usr/local/ct Mount ok! open(): No such device jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x001007ec: Read 0xffffffff, calculated 0xc7dad2d5 jffs2: Empty flash at 0x00100860 ends at 0x00101000 jffs2: Empty flash at 0x00103810 ends at 0x00104000 Configuring EMACS interfaces Bringing up interface lo Bringing up interface mii0 jffs2: notice: (493) check_node_data: wrong data CRC in data node at 0x0010379c: read 0xfba74207, calculated 0x9b1a9a93. Set promisc for device mii0 Configuring with no IP address (i.e. for PPP) verinfo=U-Boot V9.0.10P10N1 20220511143326 0x6a00000 0x1 0x83 0x8f addr==6a00000 <152>Get u32BackupBaseAddress failed! œ^qû<²îî—Žª found. data_in=0x0 data_in=0x0 insmod: can't insert '/kmodule/tagparam_mod.ko': No such file or directory pon init ZX_PA_BUF_BASE0=5da00000 ZX_VA_BUF_BASE0=dda00000 ZX_ACL_BASE=5da20000 ZX_VA_ACL_BASE=dda20000 ZX_FLOW_BASE=5de20000 ZX_VA_FLOW_BASE=dde20000 ZX_BP_BUFFER_BASE=5df20000 ZX_DESC_BASE=5ff20000 ZX_TX_UP_DESC_BASE=5ffe0000 ZX_TX_DN_DESC_BASE=5fff0000 ZX_VA_BPPE_BASE=dda00000 ZX_VA_BP_BUF_BASE=ddf20000 ZX_VA_DESC_BASE=dff20000 ZX_VA_TX_UP_DESC_BASE=dffe0000 ZX_VA_TX_DN_DESC_BASE=dfff0000 BPPE_POOL_SIZE=3000 NORMAL_BP_BUFFER_SIZE=1b00000 JUMBO_BP_SIZE=2800 JUMBO_BPPE_POOL_SIZE=200 BP_BUFFER_SIZE=2000000 lan_up=0, lan_up_port=0 g_pon_irq=26,f4000000,f0400000,f0500000,f0600000,e0c00000 get npp irq succeed,g_npp_irq:27 get tm irq succeed,g_tm_irq:29 get pp irq succeed,g_pp_irq:30 get idm irq succeed,g_idm_irq:28 enter ref_clk_set.. mode = 0 . enter pll_cfg_fractional ref_clk_set success! rxpll_ready serdes band cpu_temper:32 coarse:0x28 band calc fin pon tm init netif_napi_add() called with weight 512 on device pon DMA_DN_DESC_CNT = 0x0 DMA_UP_DESC_CNT = 0x0 pon_tm net init ok,224/176 module-netdebug: register_chrdev failed pon_pp init pon_npp init idm_status_proc success! idm_desc_init e0ae5000/5c6e0000 request idm irq succeed idm net init ok mac 0 link down mac 1 link down mac 2 link down mac 3 link down Init Pdt opticaldrv œ^qû<²îî—Žª found. pdt_motI2CProbe_func 0x50 success! ****vendor name(B0 0x14) = **** optical PN(0x60) = ¹Þâ¿Ý¯¿t!„ÿ]Ž optical PN(0x28) = œ^qû<²îî—Žª optical PN(B0:0x60) = Init Pdt opticaldrv Success register fpga driver success, major=222 = TM Module SYS FS Init ended successfully = tm_initModule begin... enter tm_sdk_init api lock init!! tm_initModule end... œ^qû<²îî—Žª found. Kmodule GN25L95.ko insmod successfully ! Init switch module g_sw_cap.sw_uni_count=4 g_sw_cap.sw_uni_mask=0xf g_sw_cap.sw_wan_port=5 g_sw_cap.sw_wan_mask=0x20 g_sw_cap.sw_all_port_count=7 g_sw_cap.sw_all_port_mask=0xef g_sw_cap.gwtype0 g_sw_cap.wantype4 g_sw_cap.onutype2 ptSwInfo->wan_logicport=-1 g_mii_dev_name[0] sw g_mii_dev_name[1] pon tm_pon_protocol_pktdeal_set fail, error protocal 33 tm_pon_protocol_pktdeal_set fail, error protocal 31 protocal fail, error deal 43 tm_pon_protocol_pktdeal_set fail, error protocal 35 tm_pon_protocol_pktdeal_set fail, error protocal 36 tm_pon_protocol_pktdeal_set fail, error protocal 37 tm_pon_protocol_pktdeal_set fail, error protocal 69 tm_pon_protocol_pktdeal_set fail, error protocal 34 protocol fail, error deal 66 [TM][dpa_set_protocol_type_i_act] failed protocol fail, error deal 65 [TM][dpa_set_protocol_type_i_act] failed -------chip_tm_init end----- [SW]set cpu queue rate limit to 8000pps Capacity=256000 Capacity=256000[SW][sw_init_switch] reg hff register npu driver 16 Init personal switch module Success correct gpon type zteGpmac_initModule begin... === GponMac Supported MaxTcont: 16 MaxPLI: 800B === = PON Module Operate ended successfully = DEbug: GPON PIN_MUX_REG3:(0x3e3f85) DEbug: GPON GPIO_PDD_REG:(0x9fac) DEbug: GPON GPIO_POSEDGE_REG:(0x4) create zteGpon_rei_task ok! = GMAC Module SYS FS Init ended successfully = zteGpmac_initModule end... Init Pdt Gpondrv gpon_Init ok Init Pdt Gpondrv Success insmod: can't insert '/kmodule/zte_xgmii.ko': No such file or directory tdm registered! zx_tdm2.0_probe! g_tdm_buf =e0b84000,5bd64000 remap tdm reg 9a106000 to f0806000 tdm irq=36 reg 0xf0800020 value is 0x20080b udpwatchd inited! kudp inited! Init codec v2.3(2019-05-17)! P_2833: Setup 0 DSP device setup OK! Database default setting is [current : X] cp: can't stat '/etc/gateinfoSCPD.xml': No such file or directory cp: can't stat '/etc/gateconnSCPD.xml': No such file or directory check for kasan supportkasanstr= not_support_kasan check for kmemleak IN task: sh(639) systools cmd: ck console [0] enabled create thread systools log success!ck run ok 11930:23:03 [OSS][Error] [pc.c(3105)main] Could not set affinity 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup 11930:23:03 [OSS][Error] [oss_cgroup.c(180)_cgroup_init] cannot access root of cgroup,kernel may not enable the cgroup F6600P login: 11930:23:05 [User][Error] [dbc_mgr_tbl.c(520)dbCreateDomainN] create table fail (GPONCFG) domain(Vendor_Specific) error default value 11930:23:05 [User][Error] [cspd_main.c(1115)pdt_proc_contro] portinfo.iWan: 64 11930:23:05 [User][Error] [cspd_main.c(1118)pdt_proc_contro] CSPGetCapPortInfo , PonType 64 11930:23:05 [gpon_mgr][Error] [gpon_adapter.c(236)gponCommInitAda] ====GPON ONU MODE==== [log_file.c(1604)ProcLogConf] Set LOG_FILE_CONF_SET_PDTCONF. [log_file.c(1652)ProcLogConf] Set cAutoSave = 1 11930:23:05 [bsp_mgr][Error] [bsp_mgr.c(338)BspMgrInit] BspMgr INIT_SUCCESS 11930:23:05 [DB][Warn] [dbc_mgr_tbl.c(1740)dbSetValComm] not find domain table(FFECfg) domain(Enable) 11930:23:05 [DB][Error] [dbc_mgr_tbl.c(957)dbSetDmDefault] default val error val() table(GPONCFG) domain(Vendor_Specific) 11930:23:05 [DB][Error] [dbc_mgr_tbl.c(4335)dbSetDmOriginal] default val error dbSetDmOriginal val() table(GPONCFG) domain(Vendor_Specific) 11930:23:05 [DB][Error] [dbc_def_gponcfg(234)dbDefGPONCFG] get RegisterID from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(266)dbDefGPONCFG] get Loid from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(280)dbDefGPONCFG] get LoidPwd from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(295)dbDefGPONCFG] get psk from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(44)dbSetRidHexVal] get ridFlag from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(64)dbSetRidHexVal] get HexRegisterID from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(122)dbSetPwdHexVal] get pwFlag from flash failed ! 11930:23:05 [DB][Error] [dbc_def_gponcfg(143)dbSetPwdHexVal] get HexPassword from flash failed ! tc utility, iproute2-ss120521 11930:23:05 [bridge][Warn] [bridge.c(2920)BridgeInit] SubScribPublish Bridge Service OK 11930:23:05 [DB][Warn] [dbc_def_dev_inf(324)dbPersonInitVer] get parameter from Flash failed!VersionMode 11930:23:05 [DB][Warn] [dbc_mgr_tbl.c(1740)dbSetValComm] not find domain table(DevInfo) domain(VersionMode) 11930:23:05 [DB][Warn] [dbc_def_dev_inf(984)dbGetParamFromV] readSoftHardWVersionCode failed 11930:23:05 [DB][Error] [dbc_def_lan_inf(56)GetValueFromCur] GetValueFromCurLine: CurLine is illegal! 11930:23:05 [DB][Error] [dbc_def_lan_inf(241)dbDefLANInfo] dbDefLANInfo: GetValueFromCurLine failed in 4 line! 11930:23:05 [DB][Error] [dbc_mgr_view.c(488)dbMgrCommViewAd] db view init fail(WDInfo) 11930:23:05 [DB][Error] [dbc_mgr_view.c(488)dbMgrCommViewAd] db view init fail(MultiWD) 11930:23:05 [DB][Warn] [dbc_mgr_file.c(1487)dbAddCfgItem] def:1 /etc/db_default_cfg.xml 11930:23:05 [DB][Warn] [dbc_person_dev_(380)dbPersonInitHVT] get parameter from Flash failed!HardwareVerTag ----------------------------------------------GetEnvPara_noproc /userconfig/env_param 11930:23:05 [binding_mgr][Warn] [bridge_api.c(699)RegisterBridgeN] RegisterBridgeNotify start, event[1] Handle[0xe46a8] 11930:23:05 [binding_mgr][Warn] [bridge_api.c(713)RegisterBridgeN] Reg RegisterBridgeNotify ok, pHandle[0xe46a8], Event[1] 11930:23:05 [upgrade_mgr][Error] [upgrade_mgr.c(2960)UpgradeInit] =====RegionCodeForTools=-14===== 11930:23:06 [DB][Warn] [dbc_core.c(588)dbPersonInitPro] Set VoIP Protocol SIP 11930:23:07 [dhcp4c][Warn] [dhcp4c_inst.c(7817)Dhcp4cInitializ] RenewRequestTimes:ffffffff,RebindRequestTimes:ffffffff iptables v1.4.13: unknown option "--queue-num" Try `iptables -h' or 'iptables --help' for more information. 11930:23:07 [dhcps][Warn] [dhcps_inst.c(999)getIFInfoAndCre] Get IFBase Info, IF_ID[DEV.IP.IF1] IN task: sh(698) systools cmd: ck ck run ok ip6tables v1.4.13: unknown option "--queue-num" Try `ip6tables -h' or 'ip6tables --help' for more information. [log_file.c(1380)ProcLogConf] Set SaveEnable=1073741815 [log_file.c(1397)ProcLogConf] Set SaveEnable=3FFFFFFF [log_file.c(2954)logFileProcMsg] operation result --- Success [log_file.c(2818)logRegisterToLogcat] RegisterToLogcat success. sip alg change power[1] ok! ftp alg change power[1] ok! h323 alg change power[1] ok! rtsp alg change power[1] ok! pptp alg change power[1] ok! tftp alg change power[1] ok! iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables v1.4.13: Couldn't find match `rt' Try `ip6tables -h' or 'ip6tables --help' for more information. iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). gpondrvCfgXGRegInfoAdapter not support now! o7_flag = 0,arg_o7_Flag->ctl=0 11930:23:09 [gpon_mgr][Error] [gpon_private_ad(199)GponRegACDNotif] switchRegACDNotify Success mt_pci_slave 0000:01:00.0: enabling device (0140 -> 0142) mt_drv_7916 0000:00:00.0: enabling device (0140 -> 0142) mt7916_init()--> Use the default iPAiLNA bin image! <--mt7916_init() ****vendor name(B0 0x14) = **** optical PN(0x60) = optical PN(0x28) = GN25L95 optical PN(B0:0x60) = 11930:23:09 [switch_mgr][Error] [switch_adapter.(855)swiser_init() return NDIS_STATUS_FAILURE tchDBInit] DB EthPortConfProduct is Aleady Full, Skip DBInit! 11930:23:09 [switch_mgr][Error] [switch_adapter.(855)switchDBInit] DB ETHRMON is Aleady Full, Skip DBInit! _SetSKUCtrl: ucBandIdx = 0 _SetSKUCtrl: TxPowerSKUEn: 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetBfBackoffCtrl: ucBandIdx = 0 _SetBfBackoffCtrl: TxBFBackoffEn = 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetSKUCtrl: ucBandIdx = 0 _SetSKUCtrl: TxPowerSKUEn: 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetBfBackoffCtrl: ucBandIdx = 0 _SetBfBackoffCtrl: TxBFBackoffEn = 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD current sync CR = 0x1 Built date: 20220608152328a Platform: ALPS HW/SW version: 0x8a108a10 Patch version: 0xffffffff current sync CR = 0x1 Chip ID: 0x13 Eco version: 0x00 Region number: 0x09 Format version: 0x02 Format flag: 0x01 Ram version: ____000000 Built date: 20220608152421 Common crc: 0xf6181f7f Release info: header tag = 0, total length = 92 tag 1, padding length = 3, tag length = 85 payload: t-neptune-main-2111-7916-imp-2212-MT7916_E1_ASIC_ROM_RAM_REBB_IMP_2212-20220608152243 Chip ID: 0x00 Eco version: 0x00 Region number: 0x03 Format version: 0x02 Format flag: 0x01 Ram version: DEV_000000 Built date: 20220608152503 Common crc: 0xe05d260e Release info: header tag = 0, total length = 0 current sync CR = 0x7 efuse_probe: efuse = 100002 [a-die version:1] IPMacTable already inited! 11930:23:23 [OSS][Error] [oss_msg.c(663)_asynSendMsg] [cspd.log_task.log_mgr] ASEND [0xAinterface is down, cmd [8be2] return!!! 2BF] to [multiapd.map.slave],(swLen=-1)<(Len=1224),path=/var/tmp/multiapd.map_asy,errno=[2:No such file or directory] ! 11930:23:23 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[wlan_config] Event[0xa204] RunTicks[1517] Wait[107] 11930:23:23 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_wps_start](7144) ioctl_set wlan0 WscConfStatus=2: errno 22-Invalid argument 11930:23:23 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_wps_start](7177) ioctl_set wlan5 WscConfMode=0: errno 100-Network is down 11930:23:23 [wlan_config][Error] [wlan_config.c(4632)handle_wlan_set] Call setup_wpsconfig fail, iRet:-1 11930:23:23 [wlan_config][Error] [wlan_config.c(4632)handlecurrent sync CR = 0x7 _wlan_set] Call current sync CR = 0x7 setup_wpsconfig fail, iRcurrent sync CR = 0x7 et:-1 11930:23:23 [wlancurrent sync CR = 0x7 _config][Error] [wlan_cocurrent sync CR = 0x1 nfig.c(4632)handle_wlan_set] Call setup_wpsconfig fail, iRet:-1 11930:23:23 [wlan_config][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) Not support for HIF_MT yet! call RT28xxPciAsicRadioOff fail !! [Nop_List_Backup] NopList Channel count:0 <---- op NULL cfg NULL cfg NULL cfg NULL 11930:23:23 [OSS][Error] [oss_msg.c(663)IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready _asynSendMsg] [cspd.log_task.log_mgr] ASEND [0xA2BF] to [multiapIPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready d.map.slave],(swLen=-1)<(Len=1224),path=/var/tmp/multiapd.map_asy,errno=[2:No such file or directory] !ser_init() return NDIS_STATUS_FAILURE _SetSKUCtrl: ucBandIdx = 0 _SetSKUCtrl: TxPowerSKUEn: 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetBfBackoffCtrl: ucBandIdx = 0 _SetBfBackoffCtrl: TxBFBackoffEn = 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetSKUCtrl: ucBandIdx = 0 _SetSKUCtrl: TxPowerSKUEn: 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD _SetBfBackoffCtrl: ucBandIdx = 0 _SetBfBackoffCtrl: TxBFBackoffEn = 0 Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD current sync CR = 0x1 Built date: 20220608152328a Platform: ALPS HW/SW version: 0x8a108a10 Patch version: 0xffffffff current sync CR = 0x1 Chip ID: 0x13 Eco version: 0x00 Region number: 0x09 Format version: 0x02 Format flag: 0x01 Ram version: ____000000 Built date: 20220608152421 Common crc: 0xf6181f7f Release info: header tag = 0, total length = 92 tag 1, padding length = 3, tag length = 85 payload: t-neptune-main-2111-7916-imp-2212-MT7916_E1_ASIC_ROM_RAM_REBB_IMP_2212-20220608152243 Chip ID: 0x00 Eco version: 0x00 Region number: 0x03 Format version: 0x02 Format flag: 0x01 Ram version: DEV_000000 Built date: 20220608152503 Common crc: 0xe05d260e Release info: header tag = 0, total length = 0 current sync CR = 0x7 efuse_probe: efuse = 100002 [a-die version:1] [log_file.c(607)AddLogBuf] Time over,NeedSave=1! IPMacTable already inited! MtCmdSetMuruCfgDlUlVal: u1BandBssSelect:0 u1Index:0 ParamUpdList:15 ParamUpdVal:0 11930:23:37 [OSS][Error]IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [oss_msg.c(663)_asynSendMsg] [cinterface is down, cmd [8be2] return!!! spd.log_task.logIPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready _mgr] ASEND [0xA2BF] to [multiapinterface is down, cmd [8be2] return!!! d.map.slave],(swLen=-1)< Capacity=200000 Capacity=200000 Capacity=200000 Capacity=200000 (Len=1224),path=interface is down, cmd [8be2] return!!! /var/tmp/multiapinterface is down, cmd [8be2] return!!! d.map_asy,errno=[2:No such file or directory] ! 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan1 WirelessMode=16: errno 100-Network is down 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan2 WirelessMode=16: errno 100-Network is down 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan3 WirelessMode=16: errno 100-Network is down 11930:23:37 [switch_mgr][Error] [switch_private_(234)switchRegACDNot] switchRegACDNotify Success 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan4 WirelessMode=16: errno 100-Network is down 11930:23:37 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[switch_mgr] Event[0x1103] RunTicks[2811] Wait[0] 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [cfg_to_ioctl](4552) ioctl_set wlan0 UseZTERateAlg=1: errno 22-Invalid argument 11930:23:37 [wlapAd->MaxHopNum = 7 n_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [cfg_to_ioctl](4552) ioctl_set wlan0 ed_chk=0: errno 22-Invalid argument 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [cfg_to_ioctl](4552) ioctl_set wlan0 tx_retry_ctrl=0: errno 22-Invalid argument [driver_wext_init]Initialize ralink wext interface Set_Bh_Bss_Proc wlan0 bandIdx = 0 ,DevOwnRole 0x20 Set_Fh_Bss_Proc wlan0 wdev->MAPCfg.DevOwnRole 0x0 11930:23:37 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_wmm](6713) ioctl_set wlan0 WmmType=0: errno 22-Invalid argument set max age failed: Numerical result out of range 11930:23:38 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_vlan_cfg](8000) ioctl_set wlan0 VLAN_Support=1: errno 22-Invalid argument IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready 11930:23:40 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[bridge] Event[0x1103] RunTicks[300] Wait[0] ffe npu is 1 ffe layer2_enabled:0 layer3_enabled:1 11930:23:40 [upgrade_remote][Error] [remote_upgrade.(1496)RemoteUpgradeIn] FirmwareUrl is illegal insmod: can't insert '/kmodule/usbcore.ko': No such file or directory xhci_plat_hcd: unknown parameter 'usbmode' ignored xhci-hcd xhci-hcd.0.auto: xHCI Host Controller creating file 'devices'creating file '001' xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66c hci version 0x100 quirks 0x00010010 xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x09100000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 4.1.25 xhci-hcd usb usb1: SerialNumber: xhci-hcd.0.auto hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb usb1: csp_report_dev_addok iMsgId = a453, vid = 1d6b,pid = 2 creating file '001' xhci-hcd xhci-hcd.0.auto: xHCI Host Controller creating file '002' xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 4.1.25 xhci-hcd usb usb2: SerialNumber: xhci-hcd.0.auto hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usb usb2: csp_report_dev_addok iMsgId = a453, vid = 1d6b,pid = 3 creating file '001' **********TOP_CRM_BASE+0x08=0x1ff7ffff****** dwc2 9000000.usb: 1792 invalid for host_rx_fifo_size. Check HW configuration. dwc2 9000000.usb: 1024 invalid for host_nperio_tx_fifo_size. Check HW configuration. dwc2 9000000.usb: 1024 invalid for max_packet_count. Check HW configuration. [log_file.c(542)AddLogBuf] Time over,LogBakBuf is full! i=1, filename=/userconfig/cfg/log, buflen=1186, bakbuflen=957, cnt=0, totalcnt=0 [log_file.c(607)AddLogBuf] Time over,NeedSave=1! dwc2 9000000.usb: DWC OTG Controller creating file '003' dwc2 9000000.usb: new USB bus registered, assigned bus number 3 dwc2 9000000.usb: irq 41, io mem 0x00000000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: DWC OTG Controller usb usb3: Manufacturer: Linux 4.1.25 dwc2_hsotg usb usb3: SerialNumber: 9000000.usb hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected usb usb3: csp_report_dev_addok iMsgId = a453, vid = 1d6b,pid = 2 creating file '001' registering usb led module! insmod: can't insert '/kmodule/usbserial.ko': No such file or directory 11930:23:42 [ddns_mgr][Warn] [ddns_mgr.c(1656)ddnsAddClientLi] call dbAPIQryView failed!DBVIEW_DDNS_SERVICE,name 11930:23:42 [ddns_mgr][Warn] [ddns_mgr.c(1569)ddnsInitClientL] Call function failed!ddnsAddClientListNode 11930:23:42 [integrate][Warn] [pdt_integrate.c(2329)IntegrateStart] Call function failed!RegisterPrefixNotify sh: can't create proc/net/kernel_panic_diag: nonexistent directory insmod: can't insert '/kmodule/usb_wwan.ko': No such file or directory 11930:23:42 [ipv6_tunl_mgr][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(Dslite) VN(DEV.DSLITE) Err(-5) 11930:23:42 [pon_dev][Error] [pon_dev_mgr.c(733)get_falsify_def] call GetTagParam failed!!!! 11930:23:42 [pon_dev][Error] [pon_dev_mgr.c(1371)FalsfyDefInitVi] call get_falsify_defend_mode failed! iRet = -7 insmod: can't insert '/kmodule/option.ko': No such file or directory >>>>>>>>>>>>>>>>>>>>>>>>gpon_omci start successed!<<<<<<<<<<<<<<<<<<<<<<<<<<< insmod: can't insert '/kmodule/cdc-acm.ko': No such file or directory 11930:23:42 [xpon_mgr][Error] [xpon_mgr.c(630)XponRegACDNotif] XponRegACDNotify Success 11930:23:42 [l2tp_mgr][Error] [l2tp_mgr.c(2047)l2tp_start_tunn] l2tp_start_tunnels: l2tp_tunnel_check failed result=-257 11930:23:42 [l2tp_mgr][Error] [l2tp_mgr.c(2096)l2tp_start_sess] l2tp_start_sessions: l2tp_session_check failed result=-257 insmod: can't insert '/kmodule/usbnet.ko': No such file or directory insmod: can't insert '/kmodule/cdc_ether.ko': No such file or directory insmod: can't insert '/kmodule/rndis_host.ko': No such file or directory 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(77)portLocateInit] portLocateInit begin 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(108)portLocateInit] portLocateInit begin set eth and lan match info tList.dwCount:12 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[1]:eth0-1 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[2]:device eth0 entered promiscuous mode eth1-2 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[3]:eth2-3 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[4]:eth3-4 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match idevice eth1 entered promiscuous mode nfo[5]:wlan0-5 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[6]:wlan1-6 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[7]:wlan2-7 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[8]:wlan3-8 11930:device eth2 entered promiscuous mode 23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[9]:wlan4-9 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[10]:wlan5-10 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(117)portLocateInit] eth and lan match info[11]:wlan6-11 11930:23device eth3 entered promiscuous mode :42 [cspd_misc][br0: port 4(eth3) entered forwarding state Warn] [portLocatbr0: port 4(eth3) entered forwarding state e_mgr.(117)portLocateInit] eth and lan match info[12]:wlan7-12 11930:23:42 [cspd_misc][Warn] [portLocate_mgr.(128)portLocateInit] portLocateInit end ok 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[3581] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[usb_mgr] Event[0xad04] RunTicksdevice nbif0 entered promiscuous mode [0] Wait[3581] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[usb_mgr] Event[0xad04] RunTicks[0] Wait[3581] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[usb_mgr] Event[0xad04] RunTicks[0] Wait[3581] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[3581] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[3580] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[3579] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[3487] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] EventIN task: sh(1120) [0x111a] RunTicksystools cmd: ck s[0] Wait[3487]ck run ok 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[3487] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[prefix_mgr] Event[0x111a] RunTicks[0] Wait[3454] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[3355] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[prefix_mgr] Event[0x111a] RunTicks[0] Wait[3355] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[3355] 11930:23:42 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[3349] [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=957 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/SecLog, BakBufDataLen=16 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[log_file] Event[0xac51] RunTicks[2] Wait[1567] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[prefix_mgr] Event[0x111a] RunTicks[0] Wait[539] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[539] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[539] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[539] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[switch_mgr] Event[0xa430] RunTicks[0] Wait[254] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[LANDEV_DHCPSOURCE] Event[0x1119] RunTicks[0] Wait[242] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[bridge] Event[0x96b2] RunTicks[3] Wait[243] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[bridge] Event[0x96b2] RunTicks[3] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[bridge] Event[0x96b2] RunTicks[3] Wait[248] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[bridge] Event[0x96b2] RunTicks[3] Wait[251] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[252] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[252] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[252] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[252] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[251] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ethlinkvlan] Event[0x96b2] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ethlinkvlan] Event[0x96b2] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[sntp_mgr] Event[0x9c52] RunTicks[1] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[sntp_mgr] Event[0x8101] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[prefix_mgr] Event[0x111a] RunTicks[0] Wait[246] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[prefix_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[ipif_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[addr6_mgr] Event[0x111a] RunTicks[0] Wait[245] 11930:23:43 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[route_mgr] Event[0x111a] RunTicks[0] Wait[245] ====================gpon_omci start====================== =====================omci sender process start===================== ==========================sys process start========================= Process_Perf's Event(4352) is not support !! Omci get Byte Order is Little-Endian =========================omci process start========================= [OADRV_VlanDefaultConfig]iRet1-257,iRet2-257 [OADRV_VlanDefaultConfig]iRet1-257,iRet2-257 Omci Debug:CmWLANListConfig.dwCount = 8 11930:23:43 [omci][Error] [vlan_module_cma(53)PortIDConvert] GetIFBaseInfo fail,DEV.ETH.IF5 11930:23:43 [omci][Error] [vlan_module_cma(2403)CmVlanDEFSet] PortIDConvert:!RET_CMAPI_OK FAILURE! 11930:23:43 [omci][Error] [vlan_module_cma(53)PortIDConvert] GetIFBaseInfo fail,DEV.ETH.IF5 11930:23:43 [omci][Error] [vlan_module_cma(2403)CmVlanDEFSet] PortIDConvert:!RET_CMAPI_OK FAILURE! 11930:23:43 [omci][Error] [vlan_module_cma(53)PortIDConvert] GetIFBaseInfo fail,DEV.ETH.IF5 11930:23:43 [omci][Error] [vlan_module_cma(2543)CmVlanUNTAGSet] PortIDConvert:!RET_CMAPI_OK FAILURE! 11930:23:43 [omci][Error] [vlan_module_cma(53)PortIDConvert] GetIFBaseInfo fail,DEV.ETH.IF5 11930:23:43 [omci][Error] [vlan_module_cma(2543)CmVlanUNTAGSet] PortIDConvert:!RET_CMAPI_OK FAILURE! 11930:23:43 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:43 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:43 [upgrade_mgr][Error] [upgrade_mgr.c(3658)upgradeProcTime] time is 50! 11930:23:43 [upgrade_mgr][Error] [upgrade_mgr.c(3673)upgradeProcTime] tagparam file same, no need copy! [FWPM]pInstList.dwCount = 0 [FWIP]pInstList.dwCount = 0 g_MeCtr_Configure=0x00000000,g_MeCtr_CreateMark1=0x00000000,g_MeCtr_CreateMark2=0x00000000 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 10, Inst does not exist! 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 11, Inst does not exist! [PON] Call CmPonGetTcont error,iRet=-6,TcontID=10 [PON] Call CmPonGetTcont error,iRet=-6,TcontID=11 [PON] Call CmPonGetTcont error,iRet=-6,TcontID=12 [PON] Call CmPonGetTcont error,iRet=-6,TcontID=13 [PON] Call CmPonGetTcont error,iRet=-6,TcontID=14 [PON] Call CmPonGetTcont error,iRet=-6,TcontID=15 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 12, Inst does not exist! 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 13, Inst does not exist! 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 14, Inst does not exist! 11930:23:43 [omci][Error] [gpon_cmapi.c(1110)CmPonGetTcont] iTcontid = 15, Inst does not exist! Sub_SNOntStaticDB:Don't create meclass:350! Sub_SNOntStaticDB:Don't create meclass:336! 11930:23:43 [omci][Error] [pon_dev_cmapi.c(309)CmPonGetIspCode] 04##################call GetTagParam failed!!!!################## call CmPonGetIspCode error! dwRet ====EVENT_O7_STATE_SAVE OFF==== = -7 11930:23:43 [omci][Error] [pon_dev_cmapiIN task: sh(1153) .c(358)CmFalsifysystools cmd: ck GetPdt] ########ck run ok ##########call Get TAG_ID_PRODUCTION_SN failed!!!!################## call CmFalsifyGetPdtSn error!dwRet = -7 Open /proc/capability/battery fail 11930:23:43 [omci][Error] [pon_basIN task: sh(1157) einfo_cm(535)cmGsystools cmd: ck etUPSInfo] cmGetck run ok UPSInfo: Get upsOnline error! Call cmGPonGetUPSInfo error, iRet = -257 11930:23:43 [omci][Error] [gpon_cmapi.c(3815)CmPonGetOmciPsk] get psk from flash failed ! Call CmPonGetPsk error,dwRet=-7 OMCI_UPGRADE_GET_CFGFILE_INFO failed power status is 0x0!!! VOP_TaskEntry entered:POWER ON!!!wState:0 11930:23:43 [BCC][Warn] [bcc_entry.c(271)BCC_TaskEntry] Unknown Event=0x00001100 when BCC PowerOn! [LHP]Update loid_authencation state wResult 0 G_ONU_REG_Authenstates 0 [OADRV_L2_Get_Onu_Response_Time]Onu Response Time(0) out of the range!!! [OMCI_me_ont_optical_transceiver_info_create]ZTE OMCI PROCESS :create ont_optical_transceiver_info me fail! ##Get management vlan about HG failed!##-zhangyc [alecal]ZTE----pon link activate success! ##O7 STATE 0##! 11930:23:44 [acd][Warn] [acd_main.c(388)acdInit] The MESH is disable. 11930:23:44 [dev][Error] [topology_dev_mg(1461)_topoDevMgrInit] SubScribPublish multiapd topo dev Service Fail!!! 11930:23:44 [base][Warn] [ieee1905_base.c(2178)_baseStart] _baseStart g_bP1905Enable: 0 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan0] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan1] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan2] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan3] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan4] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan5] mac fail. Process_Perf's Event(4355) is not support !! ParseAlarmMsg Error! 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan6] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan7] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [slave][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [slave][Error] [multi_ap_common(376)get_wlan_topolo] WlanGetCfg DEV.WIFI.RADIO1.BSS1 failed 11930:23:44 [slave][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:23:44 [slave][Error] [multi_ap_common(376)get_wlan_topolo] WlanGetCfg DEV.WIFI.RADIO2.BSS1 failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan0] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan1] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan2] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan3] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan4] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan5] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan6] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:23:44 [topo][Error] [ieee1905_socket(94)_I5GetInterface] ioctl hwaddr fail 11930:23:44 [topo][Error] [topology_main.c(378)_topoUpdateWlan] get interface[wlan7] mac fail. 11930:23:44 [topo][Error] [topology_main.c(480)topoUpdateInter] assertion 'iRet==TOPO_OK' failed 11930:23:44 [User][Error] [dnsmasq.c(846)main] |dnsmasq|bind interface socket failed 99 11930:23:44 [User][Error] [dnsmasq.c(881)main] |dnsmasq|tcp, bind interface socket failed,tcpfd:6, error=99, errstr=Cannot assign requested address br0: port 4(eth3) entered forwarding state 11930:23:45 [webd][Error] [webd_mesh_sysdi(255)_WebdNormalStar] _WebdNormalStartHandler start 11930:23:45 [webd][Error] [webd_mesh_sysdi(229)webMultiapVendo] webMultiapVendorTunSynRegSubNotify start 11930:23:45 [webd][Error] [webd_mesh_sysdi(246)webMultiapVendo] webMultiapVendorTunSynRegSubNotify end 11930:23:45 [webd][Error] [webd_mesh_sysdi(264)_WebdNormalStar] _WebdNormalStartHandler end GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param GetEnvPara_noproc /userconfig/env_param 11930:23:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(ScheduleInform) VN(DEV.ScheduleInform1) Err(-5) -----VOP_TaskEntry entered:DSP START WORopen DSP_dev driver! K!!!-------wState:1 ch:0 pcm mode:G711A_U ch 0 set pcm type is ok,val is 0! ch:1 pcm mode:G711A_U ch 1 set pcm type is ok,val is 0! Board default NO PTC slc binding cpu1.... Board default NO PTC Board default NO PTC Board default NO PTC SLC:User SLIC Driver V3.0.0 Init Finish. port:0 potsscanen is 0 port:0 Dc:0 U:48 A:20 Ring:2 VPK:70 100msEn:0, DisPowerSave:0 impe:2 ePTC:0 dwImpe:600 rxgain(D-A):-8, txgain(A-D):0 bReverseforBatteryPolarity 0 port:1 potsscanen is 0 port:1 Dc:0 U:48 A:20 Ring:2 VPK:70 100msEn:0, DisPowerSave:0 impe:2 ePTC:0 dwImpe:600 rxgain(D-A):-8, txgain(A-D):0 bReverseforBatteryPolarity 0 Find a port:0 with chan 0 cs 1 cann't Find a port:1 cann't Find a port:2 cann't Find a port:3 Init port 0 Siliconlab chip Si3219x found! id:0xaa ProSLIC:loading patch: 05042017 [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=12877 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/SecLog, BakBufDataLen=183 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 Si3219x: Channel 0 : VBAT Up = 60.32 v Register the port:0. usrline_ioctl port:1 not init usrline_ioctl port:1 not init SLC : Warning! usrline_ioctl port:1 not init SLC_Time_Cfg no config usrline_ioctl port:1 not init Read error!! usrline_ioctl port:1 not init usrline_ioctl port:1 not init usrline_ioctl port:1 not init usrline_ioctl port:1 not init usrline_ioctl port:1 not init SLC : Warning! usrline_ioctl port:1 not init SLC_Time_Cfg no usrline_ioctl port:1 not init config Read error!! Capacity=200000 Capacity=200000 sn send [LHP]Update loid_authencation state wResult 0 G_ONU_REG_Authenstates 0 rg send Set register_authencation state 5 [Leaf_omciexception]exception msg is NULL! 11930:23:51 [multiuplink][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(IPInterface) VN(DEV.OPTICAL.IF1) Err(-5) br0: port 5(nbif0) entered forwarding state br0: port 5(nbif0) entered forwarding state device wlan0 entered promiscuous mode br0: port 6(wlan0) entered forwarding state br0: port 6(wlan0) entered forwarding state 11930:23:51 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[webd] Event[0x2202] RunTicks[414] Wait[0] device wlan1 entered promiscuous mode device wlan2 entered promiscuous mode device wlan3 entered promiscuous mode 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:52 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1129 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 11930:23:52 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[wlan_config] Event[0xa205] RunTicks[2948] Wait[0] 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_wps_start](7144) ioctl_set wlan5 WscConfStatus=2: errno 22-Invalid argument 11930:23:53 [wlan_config][Error] [wlan_config.c(4632)handle_wlan_set] Call setup_wpsconfig fail, iRet:-1 11930:23:53 [wlan_config][Error] [wlan_config.c(4632)handle_wlan_set] Call setup_wpsconfig fail, iRet:-1 11930:23:53 [wlan_config][Error] [wlan_config.c(5911)DBView2WlanCfgS] handle backhaul bss ViewName:DEV.WIFI.AP8 tCfg->bEnable:0 11930:23:53 [wlan_config][Error] [wlan_config.c(4632)handle_wlan_set] Call setup_wpsconfig fail, iRet:-1 11930:23:53 [wlan_config][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) MtCmdSetMuruCfgDlUlVal: u1BandBssSelect:0 u1Index:1 ParamUpdList:15 ParamUpdVal:0 interface is down, cmd [8be2] return!!! 11930:23:53 [wlainterface is down, cmd [8be2] return!!! n_config][Error]interface is down, cmd [8be2] return!!! [pon_wlan_adaptinterface is down, cmd [8be2] return!!! e(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan6 WirelessMode=17: errno 100-Network is down 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan7 WirelessMode=17: errno 100-Network is down 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan8 WirelessMode=17: errno 100-Network is down 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_basic](5314) ioctl_set wlan9 WirelessMode=17: errno 100-Network is down 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [cfg_to_ioctl](4552) ioctl_set wlan5 VhtDisallowNonHT=0: errno 22-Invalid argument 11930:23:53 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [cfg_to_ioctl](4552) ioctl_set wlan5 UseZTERateAlg=1: errno br0: port 5(nbif0) entered forwarding state 22-Invalid argument br0: port 6(wlan0) entered forwarding state pAd->MaxHopNum = 7 Set_Bh_Bss_Proc wlan5 bandIdx = 1 ,DevOwnRole 0x20 Set_Fh_Bss_Proc wlan5 wdev->MAPCfg.DevOwnRole 0x0 11930:23:54 [wlan_config][Error] [pon_wlan_adapte(7344)__rlk_wlan_ioct] [_rlk_wlan_do_wmm](6713) ioctl_set wlan5 WmmType=0: errno 22-Invalid argument Set register_authencation state 1 [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=982 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 device wlan5 entered promiscuous mode br0: port 10(wlan5) entered forwarding state br0: port 10(wlan5) entered forwarding state device wlan6 entered promiscuous mode Open /proc/capability/battery fail 11930:23:58 [omci][Error] [pon_baseinfo_cm(535)cmGetUPSInfo] cmGetUPSInfo: Get upsOnline error! Call cmGPonGetUPSInfo error, iRet = -257 DB_RECORD_NOT_EXIST2 [OA_Sys_Mng_Pptp_Uni]GetMacBrPortMeIdFromUniMeId(UNI:257) failed device wlan7 entered promiscuous mode [Sub_SNCreateMacBrPortDesData]Sub_SNDBGetAttValueByMask failed:0,type:11 [Sub_SNCreateMacBrPortDesData]Sub_SNDBGetAttValueByMask failed:0,type:6 device wlan8 entered promiscuous mode 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(370)loopbackConfIni] LOW_IF_ID is invalid 11930:23:58 [diagnos_mgr][Error] [loopback_mgr.c(403)loopbackConfIni] FUNC fail:iRet:-2 Find a Veip Bridge Port[41217]! The Veip Triple Group[1793,41217,1] has Been signed up! Find a Veip Bridge Port[41217]! The Veip Triple Group[1793,41217,1] has Been signed up! [Sub_SNCreateMacBrPortDesData]Sub_SNDBGetAttValueByMask failed:0,type:5 common_ioctl[10:0013] ioctl failed err=[1 Operation not permitted] 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(1578)do_ioctl_of_loo] FUNC fail:cmd:19 iRet:-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(628)CmLoopbackClear] FUNC fail iRet:-2 Call CmLoopbackClearFlag error,iRet=-2 11930:23:59 [OSS][Warn] [oss_sche.c(303)RunPCB] RunPCB process[wlan_config] Event[0xa205] RunTicks[637] Wait[0] common_ioctl[10:0013] ioctl failed err=[1 Operation not permitted] Call CmLoopbackClearFlag error,iRet=-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(1578)do_ioctl_of_loo] FUNC fail:cmd:19 iRet:-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(628)CmLoopbackClear] FUNC fail iRet:-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(1578)do_ioctl_of_loo] FUNC fail:cmd:19 iRet:-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(628)CmLoopbackClear] FUNC fail iRet:-2 common_ioctl[10:0013] ioctl failed err=[1 Operation not permitted] Call CmLoopbackClearFlag error,iRet=-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(1578)do_ioctl_of_loo] FUNC fail:cmd:19 iRet:-2 11930:23:59 [omcitoplat][Error] [loopback_cmapi.(628)CmLoopbackClear] FUNC fail iRet:-2 common_ioctl[10:0013] ioctl failed err=[1 Operation not permitted] Call CmLoopbackClearFlag error,iRet=-2 br0: port 10(wlan5) entered forwarding state Calpath ... Find_Del_Priave_Bind_Br_1p failed!!!! Find_Del_Priave_Bind_Br_1p failed!!!! NextNode:[47, 511] NextNode:[281, 4095] ExExExExEx - Step Into Omci Adapter! [Omci_Hash_Icb_Deregister] error1 [Omci_Hash_Icb_Deregister] error1 [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=85 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 11930:24:02 [pon_dev][Error] [pon_dev_mgr.c(733)get_falsify_def] call GetTagParam failed!!!! 11930:24:02 [pon_dev][Error] [pon_dev_mgr.c(1337)FalsfyDefInit] call get_falsify_defend_mode failed! iRet = -7 11930:24:06 [dhcp4c][Warn] [sip_opt120.c(255)_dhcp4cOpt120Ma] param illegal 11930:24:06 [dhcp4c][Warn] [sip_opt120.c(255)_dhcp4cOpt120Ma] param illegal 11930:24:06 [dhcp4c][Warn] [sip_opt120.c(255)_dhcp4cOpt120Ma] param illegal 11930:24:07 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(ScheduleInform) VN(DEV.ScheduleInform1) Err(-5) 11930:24:07 [sntp_mgr][Warn] [time_policy.c(767)CspTpEntry] parameter is NULL! [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1595 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/SecLog, BakBufDataLen=84 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:13 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) invalid entry. no station link up. invalid entry. no station link up. 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error]invalid entry. no station link up. [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfginvalid entry. no station link up. ) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:24:14 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=6201 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:25:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1284 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=1 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 11930:27:45 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1284 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 00:01:13 [dhcp4c][Warn] [sip_opt120.c(255)_dhcp4cOpt120Ma] param illegal 00:01:13 [dhcp4c][Warn] [sip_opt120.c(255)_dhcp4cOpt120Ma] param illegal [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=234 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:01:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1284 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:03:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1284 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 00:04:48 [webd][Error] [lloglib.c(214)_logType] [usermgr_logic_impl.lua(550)__authLogin] Web user (username == xxx) is authenticated ok. 00:04:48 [webd][Error] [lloglib.c(214)_logType] [usermgr_logic_impl.lua(620)__setLogined] 192.168.1.2 -- xxx: login success [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/SecLog, BakBufDataLen=209 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 [log_file.c(1793)GetLogFilename] malloc fail. [log_file.c(2246)logParseAllLogItem] tLogItem.ItemHead.bLogTag 6E [log_file.c(1978)logGetLogFile] sFileName is /var/templog.txt 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:52 [tr069][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:05:55 [webd][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:55 [webd][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) 00:05:55 [webd][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO1.BSS1) Err(-5) 00:05:55 [webd][Error] [dbl_api.c(291)dbAPIGetView] get view failed VID(WLANCfg) VN(DEV.WIFI.RADIO2.BSS1) Err(-5) [log_file.c(607)AddLogBuf] Time over,NeedSave=1! [log_filesave.c(379)logFileSaveAction] Need to save log file, sFileName=/userconfig/cfg/log, BakBufDataLen=1556 [log_filesave.c(488)logFileSaveAction] save log file over, ToWriteLen=0, ErrCnt=0 == Agradecimentos == Pessoas envolvidas em arquivos, discussões, dicas ou bate papo em geral. Lista em ordem alfabética.